(Not yet updated for 1996 version.) Europe: Requires a tri-axial accelerometer accurate up to 2,000 g and weighing no more than 50 grams. KASK has been awarded with prizes like ISPO and Eurobike. This group is known as the CEN TC 158 / WG 11. Consequences of refusal to answerExcept in the case of legal or contract obligations (A1 - A2 of the purposes), the lack of consent may determine, for the company, the impossibility to start the processing / communication operations of its data for the purposes indicated in the purpose A3. (A requirement similar to CPSC below has been approved but not yet published.) Australia/NZ Visors ("peaks") permitted. To find out more and view the test results for all KASK helmets, please visit our web page devoted to safety standards: www.kask.com/safety. All anvils must be steel and solid without internal cavities. Most require identity of helmet under test, details of headform, number of standard, and performance data such as degree of penetration, deflection of visor in mm, whether or not positioning test band was obscured or exposed during test, elongation of strap, headform acceleration at intervals specified in standard, details of damage to helmet and its components. KASK, based in Italy, specializes in developing, designing, and manufacturing of safety helmets of the highest quality. Measurements: 4-6- 88) S slash.1.8 with any type of guide system. ASTM: Defined in base standard but not yet required by bicycle helmet specification. ("ASTM"), Standards Australia/Standards New Zealand, Australian and New Zealand standard 2063: 1996 - Pedal Cycle Helmets. cold and wet samples each impacted at sites separated by 120 mm (measured on surface of helmet) two times with flat anvil and two times with hemispherical anvil. CPSC: Must keep records on paper or electronic media showing that helmet was certified under a "reasonable testing program." Chin strap is fastened under two metal bars 12 to 13 mm in diameter and separated by center distance of 75 to 77 mm, representing the jaw, from which hangs the test apparatus, weighing 7 kg +/- 5 per cent. Oblique impacts are common in most sports (Otteet al. ASTM: Uniaxial accelerometer capable of withstanding 1000 g (9810 meters per second squared). ECE 22.06 3)Retention system strength tests on each of the first set of ambient, cold, hot and wet samples. AIS is an anatomically based, consensus derived, global severity scoring system that classifies an individual injury by body region according to its relative severity on a 6 point scale (1=minor and 6=maximal). CPSC: Entire area above the test line must meet impact standard, with impact sites centered on or above the test line. Kask is a famous company to make the track helmets. Europe: No test, but helmet strap must be able to maintain tension. Kask TEMPISH Safety. ASTM: Entire area above the test line must meet impact attenuation standard, but center of impact of the test apparatus must be at least 25 mm above the line. ASTM: Visors and face shields optional. Drop assembly exclusive of helmet must weigh 3.1 to 6.1 kg. Barometric pressure in all environments must be 75 to 110 kPa. KASK is an Italian company leader in the design development and production of helmets for cycling, skiing, mountaineering, horse riding and safety at work. Development of rotational Brain Injury Criterion (BrIC), Human Injury Research Division, UNECE Some 12,575 ASTM voluntary consensus standards operate globally. Europe: Easily legible markings throughout life of helmet Standard number, name or trademark of manufacturer, model, pedal cyclists' helmet, size in cm, weight, year and quarter of manufacturer, and "an appropriate warning" if shell adversely affected by solvents and such. KASK has always been committed to creating products that guarantee both maximum safety and comfort, exceeding all requirements set by international standards and norms in all industries within which KASK is present: cycling, skiing, horse riding, industrial, mountaineering, and beyond. Must show: (1) Identification of helmets tested and production lot; (2) Test results, including failures and actions taken; (3)test description including Helmet Positioning Index used, (4)Manufacturer's name and address; (5) Model and size of each helmet tested; (6) Identifying information including production lot; (7) Environmental condition for each helmet, including temperature, duration of conditioning and the laboratory temperature and relative humidity; (8) Results of peripheral vision clearance test; (9) Any failures to conform to labeling or instruction requirements; 10) Results of the positional stability test; (11) Results of the retention system strength test; (12) Impact test results in sequence stating location of impact, type of anvil, velocity prior to impact, maximum acceleration in g's; (13) Name and location of the test lab; (14) Technician's signature; (15) Test date; (16) Calibration test results verifying the operation of the test rig, Records to be provided to CPSC upon demand on paper or by email. This semi-aero helmet from Kask is one of the most popular helmets available, and for good reason. Kask Super Plasma Safety Helmets ANSI Z89.1 Class C This new hi-tech helmet has been specifically designed for professional work-at-height and work-at-ground application. Must have housing for triaxial accelerometer "near its centre of gravity." Impact speed must be at least 95 per cent of theoretical, implying requirement for velocity sensor. KASK are an Italian based company specializing in developing, designing, and manufacturing of safety helmets of the highest quality. KASK S.p.a. ad unico socio Via Firenze, 5 24060 Chiuduno (BG) - ITALY Phone + 39 035 4427497 Its goal is to prepare European standards for all types of protective helmets. CG of drop assembly (headform plus support assembly) must meet FMVSS 218 S7.1.8 and lie in rectangular area 28 mm by 12.8 mm. ASTM: Not to exceed 300 g. "Theoretical" drop heights of 2.0 meters (impact velocity 6.2 meters per second) for flat anvil; 1.2 meters (impact velocity of 4.8 meters per second) for hemispherical and curbstone anvils. In every field of application KASK helmets are at the forefront, be it skiing, cycling, mountaineering, horse riding, rescue or safety world. Even assuming that the statement refers to the vertical axis as it emerges from the bottom of the headform, the effect on the test area cannot be determined. Extension includes any buckle slippage. Uniaxial accelerometer capable of measuring 1,000 g's with sensitive axis aligned within 5 degrees of vertical. Headform mass varies with size, ranging from 3.1 to 6.1 kg. MIPS related results on motorcycle helemts, Peter Halldin, Division of Neuronic Engineering Royal Institute of Technology (KHT), Stockholm, Sweden. The chin strap includes a chin pad for comfort and is completely washable. We also publish and sell New Zealand, joint Australia-New Zealand, and international standards. 13 - RE 679/16 Uniaxial accelerometer capable of measuring 1,000 g with sensitive axis aligned within 5 degrees of vertical. Kerbstone anvil used "without restrictions on its orientation." AIS is the Abbreviated injury scale: The Abbreviated Injury Scale (AIS©) incorporates current medical terminology providing an internationally accepted tool for ranking injury severity. CPSC: Impacts centered anywhere on or above the test line, with sites selected for most severe test in attempt to fail the helmet. Starting from 2020, every new KASK helmet that successfully passes the CEN TC 158 / WG 11 test will be easily identified by a dedicated "WG11 rotational and linear impacts test passed" tag. KASK quality is a guarantee as a result of many carefully monitored safety tests and innovative technologies used in the designing of the helmets. Cold: -3 to -7 degrees C (F 41 degrees). The scope of the test is to measure rotational energy absorption in tangential impacts in short duration impact situations(5-10ms). There are five headforms (A, E, J, M and O) in the body of the standard and three more (C, G and K) in a table defining the test area which has 8 sizes. Sample must be tested within 1 minute after removal from conditioning environment and returned within 3 minutes or if kept out longer must be reconditioned for 5 minutes for each minute over 3. "Retention systems shall be adjustable to produce tension on straps between all shell fixing points when the retaining strap is properly fastened." Wet: Immersed in potable water at 15 degrees to 23 degrees C (F 63 to 73 degrees). Kask TEMPISH Safety. Australia/NZ Not to exceed 300 g, or 200 g for 3.0 ms, or 150 g for 6.0 ms. Drop heights of 1.45 to 1.80 m on flat anvil. The helmet must not come off of the test headform. (Holborn 1943, Genarelli1983.Kleiven et al. Grainger's got your back. KASK is an Italian company born on 2004 to design, develop and manufacture cycling, skiing, mountaineering, climbing, equestrian, rescue and work safety helmets. The brain is more sensitive to rotation than pure translational motion. These universal helmets are adjustable from 20 to 24 3/8 in (51 - 62 cm) and have an inner shell made of HD Polystyrene for ultimate protection and comfort. CEN (The European Committee for Standardization), however, is  developing a method for measuring the absorption of energy from tangential (oblique) impacts, proposed by its technical committee on head protection. Strap shall not separate or elongate more than 25 mm. $16.00. + headform nominal coefficient of friction 0,3 Cold: -18 to -22 degrees C (F -4 degrees) for four to six hours. Name and address of manufacturer, model, size, month and year of manufacture, activity helmet is designed for, not for use on motorcycles, mass in grams, shell and liner material, damaging solvents, make no modifications, fasten strap, replace after severe blow, indication of front and rear. CPSC: Velocity must be measured to an accuracy of 2 per cent within last 40 mm of free fall. Biomechanical Evaluation of Motorcycle Helmets: Protection against Head and Brain Injuries, John D. Loyd, Journal of Forensic Biomechanics https://www.standards.govt.nz Helmets tested in condition as offered for sale, and must pass all tests with or without any included attachments. In all areas where the KASK All KASK cycling helmets have undergone this test and have exceeded its requirements. A headform and drop apparatus weighing 15 kg (total preload) is positioned in the helmet and buckled in, then yanked by a 10 kg weight dropped 300 mm. ASTM: Velocity measured in last 40 mm of free fall and must be within 3 per cent of specified velocities. (Association for the Advancement of Automotive Medicine (AAAM)). in the helmet with a curved plate 100 mm in diameter underneath the liner. The Kask Zenith Helmet is non-vented with an ABS external shell to offer head protection from falls and impact. Velocity for flat anvil test to achieve 6.2 m per s and for hemispheric anvil 4.8 m per s, corresponding to theoretical drops of 2.0 and 1.2 meters. System check before and after each series of tests by dropping onto MEP a 146 mm aluminum spherical impactor weighing 4000 to 4010 g mounted on ball-arm connector of test assembly. We develop standards, technical specifications, handbooks and other publications and participate in international standards development as a member of the International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC). Final Rule that took effect as U.S. law on March 10, 1999. Impactor dropped on MEP at impact velocity of 5.44 m/s +2 per cent (drop height 1.5 m plus friction allowance). Australia/NZ Remove visor if present, place helmet on modified ISO headform, tighten strap with spacer under chin, remove spacer, put hook under edge with strap running over top of shell, pull strap in direction parallel with helmet edge with force of 50 N. After 15 to 30 seconds, helmet should not deflect enough to obscure or entirely expose a test band drawn around head between basic plane (eye level) and 74 mm above basic plane for headform J or 85 mm above for headform A. The helmet fits two headforms if it is not physically difficult to mount on the larger headform and partially compresses the fitting foam on the smaller headform. The organization's headquarters is in West Conshohocken, Pennsylvania, about 5 mi (8.0 km) northwest of Philadelphia. Ageing: none. Model # WHE00037.223 Catalog Page # 1637 ... Primary Category: ~Safety~Face Protection~Faceshield Replacement Visors Kask KAWVI00007 Zenith Polycarbonate Visor, Kask KAWVI00007-009 Zenith Polycarbonate Visor, Kask KAWVI00003 Plasma Full Face Pc Visor, Kask KAWVI00008 Zenith Full Face Polycarb Visor, Kask KAWHE00023 Zenith Ba Air Safety Helmet, Kask KAWHE00008-202 Plasma Aq Safety Helmet, Kask KAAHE00005 Superplasma Pl Safety Helmet. (Many European labs use a triple wire guidance system with headform cradled on a triangular dolly with a hole in the center which would drop away below anvil upon impact. Tolerance is 3 per cent. All KASK products are 100% made in Italy and passed through the most rigorous safety and quality tests of the KASK’s distinctive CSD Project – ComfortSafetyDesign. Temperature within the test chamber to be 67 to 73 degrees C, measured with a black standard thermometer at the same distance from the lamp as the exposed test areas of the helmet. https://www.astm.org Europe: Requires velocity sensor within 60 mm of impact accurate to 1 per cent. Data Controller InformationData Controller for the processing of personal data, pursuant to the aforementioned law, is KASK S.p.A., via Firenze, 5 - 24060 - Chiuduno (BG) - Italy. Impact sites separated by at least 150 mm. Four samples (ambient, hot. Kask UAC00002 Bag for Helmets - Multicolour 4.5 out of 5 stars 47. The CPSC has five commissioners, who are nominated by the president and confirmed by the Senate for staggered seven-year terms. ASTM International, formerly known as American Society for Testing and Materials, is an international standards organization that develops and publishes voluntary consensus technical standards for a wide range of materials, products, systems, and services. Impacts on sites selected by the testing authority to represent worst case conditions. Test is repeated with headform face pointing upward, jerking helmet from front to rear. If during testing the time out of the conditioning environment exceeds 5 minutes, the helmet is returned to the conditioning environment for a minimum of 3 times as many minutes as it was out of the environment, or 16 hours, whichever is the lesser, before testing is resumed. A major goal of WG11 is to define a test method to measure the ability of a helmet to absorb energy from a so called “rotational impact”. It's one of the best road bike helmets we've tested and … Helpful. Kask Super Plasma HD Safety Helmet. Climbing, Work/Rescue Helmet, Type 1, Class C ANSI Classification, Super Plasma. KASK helmets, based in Italy, specialises in developing, designing, and manufacturing of safety helmets of the highest quality. Kask Zenith Helmet. CEN, the European Committee for Standardization, is an association that brings together the National Standardization Bodies of 34 European countries. Wet: Immersed "crown down" in potable water at 17 to 27 degrees C (F 63 to 81 degrees). Tilt headform forward 45 degrees, attach hook to rear rim and strap run over helmet and down to a test apparatus permitting a 4 kg weight to drop .6 meters and hit a stop, jerking the strap. Base must be "monolithic," made of steel, concrete or a combination of the two, and have mass of at least 500 kg. The lightweight Kask Plasma AQ is a vented safety helmet for industrial use conforming to EN397. If helmet is to be tested for impact the area to be tested is directed toward the lamp, with the plane tangential to the outer surface normal to the radius of the cylindrical holder. ("CPSC"), Japanese Industrial Standard, Protective Helmets for Bicycle Users. Resultant test line is parallel to the basic plane and begins in front 85 mm above the basic plane, stepping down to 60 mm at a point two thirds back. Kask Safety Helmet Bag The KASK Safety Helmet Carrying Bag is the perfect accessory for protecting and transporting your helmet, keeping your helmets free from dust when you're... View full product details We assure you that, in any case, the cited subjects will only transfer the data that is necessary and relevant to the purposes of the processing for which they are responsible.We also report that they may become aware of the data concerning you, the managers of company databases as well as those in charge of the company functions related to them. Barometric pressure in all environments must be 75 to 110 kPa. We do not enforce, regulate or certify compliance with standards. Second impact on each sample except UV-wet sample is specified with "no reconditioning," which may address question of maximum time out of conditioning environment. Eight Working Groups are currently active under TC 158, and WG 11 is focused on: Shock absorption including measuring rotational kinematics from oblique or normal impact. Must be in language of the country of sale. The Kask Super Plasma HD Safety Helmet has maximum ventilation thanks to ten air intakes. Sample must be tested within 2 minutes after removal from conditioning environment and returned within 3 minutes or if kept out longer must be reconditioned for 5 minutes for each minute over 3, not to exceed 4 hours. KASK is a reference brand in the safety field. Must keep records for three years and make available to CPSC if requested within 48 hours if not on factory site. Must be made of metal and have "a low resonance frequency but not below 3000 Hz." Hot: 47 degrees to 53 degrees C (F 117 to 127 degrees) with relative humidity no higher than 25 per cent . Europe: Introduction says helmet "is intended to remain on the head in a bicycle accident and may cause strangulation by entrapment." Drop assembly minus weight of headform, ball clamp, ball clamp bolts and accelerometer cannot exceed 1.1 kg. Forward vision must be unobstructed at 45 degree angle downward from the basic plane and 25 degree angle upward from the reference plane above it. Certification label stating compliance with CPSC standard, with name, address and telephone number of the U.S. manufacturer, private labeler or importer issuing the label, uncoded month and year of manufacture, name and address of foreign manufacturer if not made in U.S. (can be coded if private labeler's name is on certificate), production lot number or serial number. CPSC: With thickest pads in place, select headform size that partially compresses all sizing pads. Strap elongation cannot exceed 5 mm per 300 mm when loaded with a 22 kg weight. Retention system tests are done after impact tests. The agency reports to Congress and the President; it is not part of any other department or agency in the federal government. The 4 kg weight is dropped for .6 m to dynamically load the retaining system while the pre-load falls away. $129.95. Price $189.00. KASK, based in Italy, specializes in developing, designing, and manufacturing of safety helmets of the highest quality. Include model, manufacturer, month and year of manufacture, no helmet can protect against all impacts warning, impact damage may not be apparent, destroy or return to manufacturer for inspection after impact, fit instructions must be followed for maximum protection, substances which may damage, recommended cleaning agents, not for motor vehicle use. *, https://www.standards.org.au/search-for-a-standard. Impact conditions are based on real accident data. (Elimination of 25 mm offset and variability with head size has been approved but not yet published.) Strap must remain intact and not elongate more than 30 mm (1.2"). Australia/NZ Flat. KASK is constantly researching and looking for ways to go beyond and improve the quality of KASK helmets even further. Helmet is stabilized in ambient conditions for 24 hours before any further conditioning or testing. In every field of application KASK helmets are at the forefront, be it cycling, downhill skiing, ski touring, mountaineering, climbing, rescue or work safety. You can also contact the supervisory authority if it considers it appropriate to lodge a complaint. During non-spray periods the relative humidity should be 45 to 55 per cent. Kask Super Plasma Work Helmet 4.6 out of 5 stars 48. + wireless system: triaxial accelerometer + n. 3 ARS The Zenith also protects against electrical hazards. These comparisons are for size medium, ISO J headform. Detailed test reports can be found here. Helmet must not lose any pieces representing more than 10 per cent of its mass during testing. https://www.standards.org.au/search-for-a-standard CPSC: Not to exceed 300 g, On flat anvil, impact velocity of 6.2 m/s +/- 3 per cent typically requiring drop height of 2.0 m plus any height adjustment for friction losses. Introduction notes that "concern has been expressed that rigid peaks may cause rotational injuries to the head or neck during some falls, and facial injuries if they shatter or break off." Australia/NZ Various records for different parts of test protocols. Europe: Following the strength test the buckle must still be openable with one hand. Aging: Exposed for 48 hours to a 125 watt xenon-filled quartz lamp at 250 mm followed by spraying for four to six hours with 1 l. of water per minute at ambient temp (not specified). Size O is very large, for helmets with inside circumferences of 620 mm. regardless of size. MEP must be 152 mm in diameter and 25 mm thick, with durometer of 58 to 62 Shore A, fixed on flat 6.35 mm aluminum plate. The limits KASK has defined or this test are also based on the following studies and norms: Development of rotational Brain Injury Criterion (BrIC), Human Injury Research Division, UNECE, Development of Brain Injury Criteria (BRIC), Stapp Car Crash Journal, MIPS related results on motorcycle helmets, Peter Halldin, Division of Neuronic Engineering Royal Institute of Technology (KHT), Stockholm, Sweden, OBLIQUE IMPACT TESTs Mass of anvil mount at least 130 kg. You did not add any gift products to the cart. Europe headforms conforming to EN 960, Headforms for Testing Protective Helmets. Vertical drop towards an 45degree impact angle. The commissioners set policy for the CPSC. Kask, from Italy specialises in the development, design and manufacture of safety helmets of the highest quality. over the wavelength 280 nm to 800 nm, either measured or calculated. The Kask Protone uses Kaske’s Octo Fit adjustment system, which helps to make the Kask Protone one of the most highly adjustable road helmets on the market, and one that fits an extremely wide range of head shapes. Ageing: none. The Zenith also protects against electrical hazards. ASTM: Complete test record must be kept for all certification testing performed by manufacturer or independent lab on paper, electronic format or photographs. Helmet is supported on a headform and preloaded with bean bag filled with 5 kg of lead shot. Examples include the roll-out of project teams in the Washington, D.C. area, mandatory deployment on the I-5/SR-16 Project in Tacoma, WA, where 150 helmets were bought and are in use and at the SFO Air train project in San Francisco, CA. I have read the information pursuant to Art. (Dimensions usually vary with head size. It is lightweight, compact, comfortable and well-ventilated with its 10 air intakes that that provide efficient cooling and ventilation. $129.95. (For buckle and strap strength see Retention System. Standards New Zealand is a business unit within the Ministry of Business, Innovation and Employment. Kask an Italian helmet company who specializes in developing, designing, and manufacturing of safety helmets in the highest quality. On hemispherical and curbstone anvils impact velocity of 4.8 m/s +/- 3 per cent typically requiring drop height of 1.2 m plus friction adjustment. Also requires record of the parameters and results of retention tests, name and location of the test lab, signature of the technician performing the test, test date and calibration test results. KASK's mission is to maintain a perfect balance between technological excellence, functionality, safety, and attractive design in their products. 1999, Verschueren2009, Mellor and Chinn 2006) 9.1K likes. None of the protective components can become detached during impact test. We are not able to describe the lines with the info we have. (May have been updated for 1996)  Weight of support arm cannot exceed 20 per cent of mass of drop assembly, which is limited to 3.5, 4.0, 5.0 and 6.0 kg for the four headform sizes ABCD. At 28 mm in front of the axis it begins to rise again and at 34 mm in front of the axis it reaches 54 mm above the basic plane. #218 (rev. Founded in 2004, KASK is a relatively young company, yet already thanks to a talented team of expert engineers and partnerships with Italy's market-leading factories,in this short time the company has gone through a tremendous evolution marked by success all along the way. Headform: EN960 serie Australia/NZ No velocity sensor specified. Kask HP Plus Ventilated Safety Helmet with Chinstrap and Adaptor - White. Headform to be "smallest and largest claimed for that helmet type." Australia/NZ Permanent and legible letters no less than 1.5 mm high and visible without removing padding. ASTM: Ambient: 17 to 23 degrees C (F 63 to 73 degrees) with a relative humidity of 25 to 75 per cent . Peak acceleration should be between 381 and 397 g. If results of pretest and posttest impacts differ by more than 5 per cent equipment must be recalibrated and test results discarded. The Plasma AQ’s lightness is made possible by the high-density polystyrene insert, which absorbs impact forces. Kask Safety Helmet Bag. Safety helmets, Visors and Hearing protection. TC 158 is the Technical Committee dedicated to the head protection inside CEN. Ageing: none. Original paper copy of test summary must include manufacturer's name and location, model and size of helmets tested, identifying code for each helmet in each conditioning environment, observed temperatures in each conditioning environment, relative humidity and temperature of the laboratory, impact test results in sequence with location of impact, anvil, velocity and maximum acceleration. Sale-39% Back to Helmets. Nature and purpose of the processingA1) pre-contractual and preliminary information regarding the stipulation of the contract; A2) contractual execution and its administrative management;A3) market analysis and statistics, sending advertising, promotional or information material on the group's activities, including newsletters, checking customer satisfaction;As part of the commercial relationship, not all the information given or collected is mandatory, but also the optional ones (A3) are indispensable and useful for maintaining and developing the relationship over time. 2006, Deck et al 2007). The CPSC is headquartered in Bethesda, Maryland. Australia/NZ Ambient: 18 degrees to 25 degrees C (F 64 to 77 degrees). Velocity of headform must be equivalent to a drop height of 1.49 to 1.51 m. ASTM: Peripheral vision of 105 degrees from centerline required on both sides. Kask Plasma AQ Helmet. We form technical committees made up of stakeholders from government, business, industry, community, academia and consumers. oblique tests @ 45°, impact speed 6 m/s, BrIC < 0,68 Australia/NZ Four single impacts anywhere above test line, separated by not less than one-fifth of the circumference of the helmet measured at "the nominal AA' line," shown as 12.7 mm above the Reference Plane. Its goal is to prepare European standards for all types of protective helmets. Angelo Gotti, CEO of KASK, is recognized as one of the world's leading helmet experts with more than 30 years of experience in various industries. Development of Brain Injury Criteria (BRIC), Stapp Car Crash Journal